Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterTrusted Garage Door Installation for Fort Worth Homeowners
A new garage door installation in our Garage Door Installation in Fort Worth typically runs $700 to $2,200 for the door, tracks, springs, and labor. That’s the number range we quote before we ever touch your hardware. And if you measure your opening, send us photos, and clarify the material, you’ll get a flat, written price before any work starts, because that’s Clause 1 of The Haven Standard, the documentation system Servo Garage Doors has been operating under since 2015.
We’re not here to sell you a door by selling you urgency. We’re here to tell you what it costs, show you what we found, and install it so it opens and closes without noise, sag, or binding. Marcus Deller runs our Fort Worth operation, and every technician arrives in uniform, background-checked, with the license number on the page, not tucked into the fine print. If you need a quote, call (682) 297-6476. A real person answers, 24/7.
What Our Garage Door Installation Service Includes
Installation means more than hauling away your old door and bolting a new one in. We replace or inspect the sections, the spring system, the track, the rollers, the hinges, and the operator interface, then tune it as a unified mechanism. Every Fort Worth installation ends the same way: a documented photo record of what was installed, what was replaced, and what the door looks like under load, delivered to you before we leave. That’s not an add-on. That’s standard.
New Door Installation
A new door installation is the full replacement of the existing door and its working hardware. Homeowners typically do this when a door is bent beyond panel repair, rusted through at the bottom section, or so old that replacement parts aren’t manufactured anymore. We measure the rough opening, check the side room and headroom clearance, then specify a door that matches the existing track geometry or replace the track system entirely if it’s undersized for the new door weight.
Single Car Door
A single car door runs about 8 to 9 feet wide and 7 feet tall in most Fort Worth garage plans. The job takes one technician roughly 3 to 5 hours including removal, new track and spring installation, and balance testing. We quote the door, the spring, the track, and the weatherseal as one flat price, so the number on your estimate is the number on your invoice.
Double Car Door
Double car doors are 16 feet wide in the standard configuration, which means the track, spring, and panel loads are heavier and the balance has to be dialed in with more precision. We do this every week in Fort Worth and the surrounding suburbs, and we know the local wind load requirements that affect 16-foot door sections in exposed north-facing exposures. A double door install typically starts mid-morning and is done the same day; the written price covers the second pair of hands when needed.
Custom Garage Door
A custom door usually means a non-standard width, a non-standard height, a specific wood species, or a design drawn by an architect rather than pulled from a catalog. We spec it with you in writing: section profile, panel stamping or overlay, glass configuration, cladding, insulation, and opener compatibility. You’ll get the shop drawing and the dollar figure before you commit, and you’ll get the manufacturer’s lead time in the same conversation, since custom doors in Fort Worth can run 4 to 8 weeks from order.
Steel Doors
Steel remains the most common material in Fort Worth because it handles hail season without cracking and doesn’t warp in North Texas humidity the way solid wood can. We install steel doors with either polystyrene or polyurethane core insulation, and we’ll tell you the R-value difference straight, not as a sales prop. The steel door quote includes reinforcement at the opener bracket, because that’s the point that fails first when a door is under-spec’d.
Wood Doors
Wood doors are a different discipline. They’re heavier, the sections swell and contract with Fort Worth’s temperature swings, and the spring has to be engineered for the actual panel weight, not a spec-sheet guess. We’ve installed builders, paint-grade, and stain-grade wood doors on older Fairmount homes and in new builds out in Benbrook, and we photograph the door’s moisture content at the job start because wood that hasn’t acclimated will move after install. A wood door in Fort Worth requires a maintenance regimen, and we’ll explain it before you pay for it.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Garage Door Installation
We install and service Chamberlain, Genie, Clopay, and Amarr, among others. On the Chamberlain side, we’re familiar with their belt-drive opener geometry and the way their motor rpm’s interact with heavier custom doors, so we can set limits and force settings correctly on day one instead of chasing phantom reversal faults later. Genie openers show up on a lot of 2015 to 2020 Fort Worth builds, and we know their wall console wiring and the older Intellicode receiver patterns well enough to pair your existing remotes to the new opener during the door install.
Clopay and Amarr are the two door manufacturers we install most often. Clopay’s steel door section profiles let us match an existing door on a partial replacement when the damage is contained to one or two sections. Amarr’s class lineup differs by series frame and insulation package, and we can tell you which series is worth the money based on whether you park in the driveway or use the garage as a workspace. Whether your current unit is a Wayne Dalton, Raynor, or Craftsman, we can pull the model and the year, check what’s still supported, and give you a straight answer on repair versus replace.
BeforeAfterSigns You Need Garage Door Installation Right Now
- Your door sags at the center when open, or won’t hold position at half-height. A door that drifts up or down on its own usually means a fatigued or broken spring, but if the door sections are sagging or bowing at the middle, the door’s structural integrity is the problem. In Fort Worth garages with west-facing exposure and high afternoon heat, we see this in steel doors that took a hailstorm hit and lost their crown. A door in this condition is dangerous and will only get worse.
- You can see daylight through the door sections or the bottom weatherseal is rotted. Gaps at the section joints mean the hinges are wearing the panel stiles ragged. Gaps at the bottom mean the seal has died and water is getting into the garage. During Fort Worth’s spring storm season, water intrusion starts as a mildew smell and ends with ruined drywall and swollen baseboards.
- The door shudders, binds, or scrapes against the track on the way down. Noise you can hear from the living room is a mechanical problem, not an aesthetic one. A door that’s binding is chewing up its rollers, and the added resistance is shortening the spring life. The door is fighting the track, and the track is losing.
- The bottom panel is rusted through or dented to the point the door won’t seal. Fort Worth’s humidity and rain cycles are rough on unprotected steel. A bottom panel that’s rusted at the stile won’t hold the weatherseal, and a rust-through at the bracket is a failure waiting to happen. In most cases, one bad bottom section is replaceable, but if the rust has spread to the adjacent section and the door is 15-plus years old, a full install is the smarter spend.
- You bought the house and the door is original to a 1970s or 1980s build. Older Fort Worth homes in Wedgwood, Handley, and Ryan Place often still have original wood or builder-grade steel doors. They’re usually single-wall steel, have no insulation value to speak of, and their spring system predates the modern center-bearing torsion standard. If you’re already renovating, replacing the door before it fails is a quantity you can plan for, not a Saturday morning surprise.
Our Garage Door Installation Process - Step by Step
- 1
Measure and document. We measure the rough opening width, height, side room, and headroom, and we photograph the existing door, track, and hardware before we give you any number. This is Clause 4 of The Haven Standard, and it exists so you can see exactly what we’re working with.
- 2
Flat written price. Before any work starts, you get a written price and scope: the door, the hardware, the labor, the haul-away, and the tax. If anything changes, you see the change order before we execute it. No surprises on the back end, no “while we’re in there” upsells.
- 3
Removal and prep. We pull the old door, inspect the existing track for usability, and check the jamb points. If the old track can be reused, we tell you and discount the price. If it can’t, we explain why and show you the photo evidence.
- 4
Install and tune. The new door is installed, the spring is wound to the calculated tension, and the opener’s limits and force settings are dialed to the door’s actual weight. At Servo, we run the door through 10 full open-close cycles and listen for chatter at every hinge point before we call it done.
- 5
Document the job and walk you through it. You receive the photo record, the written warranty, and the final invoice. We’ll show you how to test the safety reversal, where the warranty covers, and exactly what we’d do differently next time. Then we drive away and you can verify everything we just told you.
How Much Does Garage Door Installation Cost in Fort Worth?
New door installation in Fort Worth runs $700 to $2,200 for a standard single or double door, including sections, track, spring, hinges, rollers, weatherseal, and labor, as detailed in our Garage Door Installation cost guide. A basic single steel door without opener replacement starts near $700. A 16-foot insulated door with a real opener lands in the $1,200 to $1,700 range. A custom wood door in a stained finish with heavy-duty track and upgraded spring will push over $2,000.
What drives the price: door size, material, insulation, whether the existing track can be reused, and the condition of the surrounding framing. Fort Worth’s freeze-thaw cycle also factors in; doors with untreated bottom sections and rusted tracks take longer to remove cleanly. The way to avoid overpaying is to get a flat, written price before the work starts and to refuse any quote that says “plus materials” or “we’ll see what happens.” Our free estimate includes the complete scope, so there’s no vague line item you’ll owe later. A good install in Fort Worth is not a guessing game. It’s a measured, quoted, documented job.
Garage Door Installation Near Fort Worth - Our Service Area
Servo Garage Doors Fort Worth covers the full metro area, including Garage Door Installation in Haltom City and Garage Door Installation in Saginaw. We also work in Watauga, North Richland Hills, Benbrook, Hurst, Keller, Bedford, Colleyville, Arlington, and Euless. Most installation jobs are scheduled within 2 to 4 business days; we keep a limited number of same-week slots for straight-forward steel door replacements. If you’re checking whether we cover your address, call and ask. The person who answers knows the map, not a call center script.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Garage Door Installation in Fort Worth
Garage door installation is the full replacement of your existing garage door and its working hardware, including the sections, track, springs, and often the opener. At Servo, we measure the opening, spec the correct door, provide a flat written price, and complete the work with a documented photo record. Whether it’s a single car door in North Richland Hills or a custom two-car door in Arlington, the process is the same: quote first, work second.
A standard single door install takes 3 to 5 hours, and a double door typically takes a full day including removal and spring tuning. Custom doors with non-standard track or high-lift hardware may take longer, but we’ll give you a straight time estimate before you commit. Installation is scheduled, not urgent; you’ll get a day and a time window, not a vague “sometime this week.”
New door installation in Fort Worth typically costs $700 to $2,200 for a complete door with labor and hardware. Single steel doors start near the bottom of that range; insulated doubles and wood custom doors run to the top. A written flat price before work starts means that number doesn’t move when the technician arrives. Call (682) 297-6476 for a free estimate and the actual number for your opening.
Yes, we install and service Clopay, Amarr, Chamberlain, and Genie doors, among others. We can work with your existing Clopay sections or install a full new Clopay door matched to your current track and opener. If your Clopay door is still under manufacturer warranty, we’ll help you work through that process too.
Installation is scheduled work, not emergency work. If your door fails and can’t be repaired, we can often fast-track a replacement within 2 to 3 business days, and in some cases same-week. Emergency garage door repair is available 24/7, including weekends and holidays, with a live person on the line every time. The installation side of the business runs on measurements, estimates, and written scopes, not frantic dispatch.
Every new door installation from Servo includes the manufacturer’s warranty on the door and our 365-Day Done Right Promise on the workmanship. If it’s not done right, we make it right. The details are in writing, on the terms page, not handshake-deep. The photo record we deliver at close-out is your documentation of what we installed and how it’s performing.
Clear the area around the door by at least 3 feet, unplug or remount anything hanging on the door or track, and move vehicles out of the garage before the tech arrives. We handle the rest, including haul-away of the old door and the existing hardware. If you have a home security system wired to the door, it’s worth checking whether the sensor is mounted to the track.
Schedule Your Garage Door Installation Service in Fort Worth Today
Call (682) 297-6476 and mention your door size and material. You’ll get a flat, written price before work starts, no obligation. If you already have an estimate from another company, bring it in and we’ll give you a free second opinion. We answer 24/7, because a garage door doesn’t fail on a schedule.
Written by Marcus Deller, Owner at Servo Garage Doors Fort Worth, serving Fort Worth since 2015.